Showing posts with label deck. Show all posts
Showing posts with label deck. Show all posts

Wednesday, August 19, 2009

PHEW! Dodged a bullet

hey guys. i was planning to have it all glueing tonight and ready for christening tomorrow but I ran into a bit of a problem. in fact, it was a 'holy crap i'm not, not the battleship, the whole project is over' type problem. ya, pretty frightening. heres what happened.

so, like i said, i zip tied all the wires to the sides and to the various components such that there was minimal stress on the leads and also to keep as organized as possible. i showed you a picture yesterday of that. well, sometime yesterday and then also today, the speed controller started acting up. i went and read the instructions for the ESC (a piece of junk manual) and learned of a possible issue that i then internet researched and learned i should do something about it. i needed to remove the positive battery wire so that the bec (which i just learned about today and is basically like an internal battery) wouldn't interfere with the actual battery. so i did. then things stopped working. by things i mean the speed controller wasn't passing on voltage. 7.4 V in, .1 V out. essentially, BAD. so i put back the wire. still nothing. i started disconnecting things left and right. BY THE WAY. this was right before i was about to go out and do a last pre-deck test before assemblying the deck. i had already put on the back deck

and taped it up to keep out the water as best as possible. so i was super excited to go and test both the drive and the pump. (if you notice the water gun video, the boat is not moving. thats because the problem was on and off that day too. thats why i went looking at the manual, thats why i did the research and pulled the positive battery wire. thats where our story started) however, it was not to be. like i said the ESC wasn't working and i was flipping out. i removed all sorts of things and nothing was helping. i broke out the voltmeter and worked back from the motors. .1V at the motors. .1 at the parallel split point. .1 after the ESC. 7.4 before the ESC. obviously, something was wrong with the ESC. what? Spent all afternoon debugging. nothing.

i called my contact, looking for help, right around dinner time. that wasn't really very considerate, but i was getting desperate. this isn't a part i can replace in lest than a week or so. and i go to vassar in exactly a week (HOLY MOLY THATs EXCiTING!). so this kills the project.

like last time, i described stuff to him, he suggested some things i had already tried, so i threw out some possible keyterms that might help him remember a solution. but this time, didn't help.

i went and had dinner, after which stephen called back with a new suggestion. didn't help. we agreed to talk again tomorrow before giving up. after the call, i was upset and so i started over again. this time i took EVERYTHING out. no servos connected, no pump system, just the battery to the ESC to the voltmeter. and it worked! so i started putting things back in, hoping it would stop working at some point so i would know what the problem was. if i got all the way to the end, i'd be nervous that it was just being spotty again and i hadn't fixed anything.

however, i put in the rudder servo and it stopped working. it turns out, the rudder servo fits in right-side-up and upside-down. upside-down screws up the reciever and also the ESC. so, flipping over the rudder servo kept things working. i kept adding things on. the next thing that disrupted the system was the switch+fuse that i installed. i didn't figure out why tonight, but i'll look into it tomorrow. i was just happy to have figured out what happened. and rather, i was just happy to have a working ESC.

so, while i didn't get much done today - though i installed the back deck - i still have a project. that is, i'm not hosed. which is good. :)

Tuesday, August 18, 2009

system check 2 (minus the sinking)

the waves couldn't sink me this time. well, they could've, but i didn't let them!

i patched up the broken leads and resoldered everything, and ziptied all the wires to make it slightly less chaotic. take a look.

and, if you're not familiar with electronics projects, thats fairly clean. go back and check it out before, on the blog maybe like 4 or 5 days back.

k, so we got everything working and then we headed out to the lake. the first time we didn't get any photos. plus, another lead snapped off so i took it back, fixed it, then we headed back out. take a look.


woOOOooo! it works!! i'm so stoked!! i took it back in and this afternoon i've gotten to work on how the deck will connect. i'm going to epoxy these guys to the side of the hull then screw the deck into them.





i'll put rubber underneath so that it'll be mostly water tight. then the only way for water to get in is the place where the deck portions meet.

might be real launch tomorrow, might be thursday.


P.S. check out my dad's project.

so the story is, when i was little, we went fishing and we sat on the bank for hours, never even getting a bite! at the end, i asked him, in with my youthful innoncence, "why do they call it fishing? theres no fish involved." so, this time instead of randomly throwing in the line, he's taking an engineer's approach. he went out and got an underwater camera, and some camera (cyclops) glasses

so he's going to spot the fishes, then catch them. or thats the plan. today's update is that you can't really tell what you're looking at. its just blue in all directions. EXCEPT when you hit the camera on the bottom of the lake. then you see the sandy bottom. hehe. he'll get it working. and so will i!

Saturday, August 15, 2009

what does it laquer?

hey, new follower (pushes us up to a monstrocious four),

today took a change of plans. instead of installing everything, i decided it was more important to go seal all the wood so it would be mostly waterproof for installation than to do it afterwards. i'm supposed to wait 24 hours for the second coat, but i decided 3 was enough... hehe... watever, its just the pump bases so its not critical. the top decks and sub decks i'm going to wait out the appropriate time and thats both because its way more important and i can afford to wait cause the soonest i'll need the decks will be tomorrow evening. so if i laquer them tomorrow morning, i'll be somewhat good.

funny story about the laquering, i did it and then had no thinner to get it off my hands. so i had to wait half an hour with sticky hands while my dad got some thinner.

Friday, August 14, 2009

get ready for installation




hey guys!
so the sub pump is installed, i believe i told you that yesterday, but its now funcional! i went and tested the pumpage and it works well :)



also, i kept working on the bases for the various components. i bulit a holder for the rc reciever

i've laid out the whole interior so i'll start glueing in components tomorrow. after that i have to outfit the decks - install the subdecks, figure out how to secure the main decks, split them up, then put in the connectors and switches. all that is

Sunday, August 2, 2009

saturday blog (on sunday)

i missed blogging yesterday so i'm doing it this morning.

got some free manual labor from daniel yesterday. he fitted the new radio box to have the cords come out and remain somewhat waterproof. pretty sweet! oh, and he also made a temporary boat stand. it'll do for now, but i'll go make a super nice one after i'm all done.

as for what i did yesterday. i finished installing the motors. but not really. that damn second motor is too high again so i have to redo it AGAIN! i'm so frustrated with the sucker. i also started outfitting the top deck. well, not really, i made a practice deck to be working on and made measurements and cuts into that so that i wouldn't ruin the actual deck. its mostly done so i have to go take the plunge and work on the real deck today. and then maybe i'll solder some today too. we'll see. i got up crazy early so i'll have plenty of time!